Despite the appearance on the market of inexpensive and practical materials, copper pipes are still successfully used for the assembly of internal wiring of heating circuits. But copper is an expensive material, so the installation of copper heating pipes should be carried out by carefully studying the norms and rules.
The efficiency of the finished system depends on the quality of the equipment and the skill of making the connections.
Let's look at the features of copper pipelines for heating and the technology of their installation together.
Differences in copper piping for heating
Copper has a whole range of positive qualities, thanks to which it stands out from the rest of the materials. If the construction project allows the use of such expensive elements, then for the internal wiring of the heating system, you should purchase a set of copper pipes and fittings in the amount hammered into the estimate.
Pluses of copper pipelines:
- the ability of the metal to expand allows you to easily tolerate the high temperature of the coolant, sudden temperature jumps and even freezing of water;
- for the same reason, copper perfectly withstands pressure drops in the network, as well as possible water hammer;
- the reddish metal is resistant to hard water containing impurities - lime, chlorine, etc .;
- the material does not have perfect smoothness of the inner walls, but a low degree of roughness protects against the formation of limescale and creates little resistance to the movement of the coolant;
- copper is known to resist the development of pathogenic bacteria and the formation of mold;
- the combination of strength and softness allows you to create pipelines of various designs;
- in some cases, the heating wiring performs a decorative function, although safer copper circuits of the HVS or gas pipeline are recommended for room decoration.
To prevent foreign matter from being deposited on the pipes and not reducing functionality, special requirements are placed on the coolant: the water must be clean, filtered.
But copper pipes have their drawbacks, the main of which is the high cost. If we take for comparison two meter-long pipes with a diameter of 26 mm made of metal-plastic and copper, the first will cost 147 rubles, and the second - 486 rubles. It turns out that the copper wiring will come out more than 3 times more expensive.
Using metal pipes to arrange heating circuits, one should not forget that they can heat up to 70-80 ° С, thereby posing a threat to the health of residents
Copper is selective for other metals, so fittings should be selected carefully. Aluminum, duralumin or steel parts cause an electrochemical reaction and rapid corrosion.
Therefore, usually use either "native" copper connectors, or brass, bronze, chrome or nickel. Tin or solder PIC is used only in the soldering process.
Pipe Regulatory Requirements
If copper as a material is completely satisfied and the cost of the products does not bother, it is necessary to check the compliance of all system components with state standards.
Information on pipe manufacturing standards can be found in GOST R 52318–2005 “Copper pipes ...”, which lists the requirements for copper products for cold water, hot water, gas supply, and steam and water heating
Documents governing the installation of wiring are also useful - STO NP “AVOK” 6.3.1–2007 “Pipelines of copper pipes ...” and SP 40–108–2004 "Design and installation ...". The requirements for the product range, the composition of the coolant, and the characteristics of the pipes are separated by individual items.
Data tables and graphs will help with the selection of solders. Material about anticorrosion protection, repair work and calculation methods may be useful.
Technologies and rules for installation
To begin, consider the general rules regarding the installation of copper pipelines. As you know, metal is an excellent conductor. To provide protection against stray currents, as well as reduce the risk of corrosion, you can use products in a polymer shell.
Image Gallery
Photo from
Possibility of using lead solder
Connection of copper and aluminum parts
Using brass fittings and adapters
Which radiators are best for copper systems
In private practice, it is quite rare, but in industry assembly of pipelines from steel and copper is still used. In this case, it is recommended that steel be used for risers, and copper for wiring, that is, steel products should be in the first position according to the flow of coolant. Magnesium connectors are required.
There are several ways to connect products, the choice of each of them depends on the specific situation:
- capillary soldering with solder;
- compression fittings;
- pressed fittings;
- threaded installation.
The latter method is practically not used, because it has lost its relevance. Soldering and crimping differ in the degree of laboriousness, the technique of execution, the presence of different tools, but are equally in demand. Consider three popular piping technologies.
How to connect pipes by capillary soldering?
Soldering takes longer, but the joints made are durable and leakproof. The best option for solving everyday problems is the use of soft solder. The operating temperature does not exceed 250 ° C.
The use of brazing alloy increases the strength, but expensive equipment and special conditions will be required for the work, since the soldering process takes place at a temperature of more than 700 ° C.
With the help of soldering, one-piece joints are created, which are performed either by the bell-shaped method, or by means of fittings. With bell-shaped technology, one end of the pipe must be expanded so that when the elements join, a gap of 0.2-0.3 mm wide is formed between their walls.
It is filled with solder, after which a sealed connection is created. But take a closer look at soldering with a fitting, the most popular among installers.
Materials and tools for work
It is necessary to prepare copper pipes and fittings, but not the first sight, but specially designed for soldering.
Soldering connectors and adapters are distinguished by a smooth surface and the absence of additional grooves, nuts, rings, etc. They can have a straight, angular, cross shape - depending on the purpose
Tools for performing work:
- gas burner - sufficiently propane;
- pipe expander (calibrator);
- pipe cutter, as scissors for metal deform the shape of the pipe;
- chamfer;
- devices for cleaning and polishing (fine sandpaper, brushes, rags).
When choosing solder, it is better to dwell on the option with a tin base. In addition to tin, bismuth or silver may be included in the solder. This type is good in that its melting point is much lower than that of copper products.
Read more about solders for brazing copper pipes can be found in this material.
During the soldering process, the solder will assume a liquid state and will be able to hermetically fill the connecting gap, while copper elements will not respond to high temperature.
In addition to solder, a flux is required. This is a kind of lubricant for parts of elements that need to be docked. The flux is carefully applied with a brush to the surface of the pipes and fittings
For the convenience of installation work, you can use special fittings for low-temperature soldering. They differ in that at the ends they have a narrow groove filled with solder.
Low-temperature (soft) soldering is typical for domestic work, and high-temperature (hard) is used in production. A hard look is also used when connecting air conditioning pipes and refrigeration units.
Description of the soldering process
Copper is a malleable material, it is not difficult to work with it, but in the absence of experience it is better to first practice on unnecessary pipe sections.
Image Gallery
Photo from
Using a pipe cutter, a special tool, we cut the elements. It is better to perform operations directly during installation, so that, if necessary, adjust the length
Insert the chamfer into the pipe and rotate until we remove the edge that arose during the cutting process. This is necessary so that the inside of the pipe does not become narrow
First, with the same chamfer, but its other side, and then with a fine sand, we process the outer side of the pipe so that there are no scratches and the copper shines
To increase the efficiency of soldering, it is necessary to carefully clean the second part - a corner, an adapter. A suitable tool is a screwdriver with a nozzle from a regular brush
An ordinary glue stationery brush is suitable for applying flux. We take the solution in small portions and distribute a thin layer on the surface of the pipe
The prepared cleaned corner is put on the end of the pipe covered with flux. To make the connection more tight, screw the pipe into the corner with light movements
Before starting soldering, remove excess flux or paste. An ordinary rag is useful for this. When the surface is completely cleaned, for convenience, the part is fixed in a vice
In one hand we take solder, in the other burner and we begin to carefully solder. After heating the pipe, we place the solder at one point, thanks to the capillary principle, it will spread throughout the entire area
Step 1 - cutting a copper pipe into segments of a given size
Step 2 - removing the edge with a chamfer
Step 3 - preparing the outer wall for soldering
Step 4 - processing the inner surface of the corner
Step 5 - applying flux or paste to the end of the pipe
Step 6 - twisting the end of the pipe into the corner
Step 7 - cleaning the junction with a rag
Step 8 - Soft Soldering Process
The connection must be allowed to cool, and then thoroughly rinse the junction with clean water. If you do not remove the solder residues, over time they will provoke corrosion. It is not recommended to speed up the cooling process with cold air or water, under natural conditions, the compound is cooled for 7-10 minutes.
We also recommend that you read the step-by-step instructions for soldering copper pipes. Read more - read on.
Safety precautions
Soldering, unlike crimping methods of connection, is a dangerous event, during which it is necessary to use protective equipment. In addition to working clothes made of dense material, it is necessary to wear gloves, as well as glasses with special glasses or plastic.
Manipulations with a burner require attention, accuracy and professionalism. The tool must be serviceable and the fuel must be suitable in composition. Better to use devices with convenient piezo ignition
Some types of solders contain fluorine and cadmium, and when the flux is heated, harmful compounds are also released, so for the duration of operation it is necessary to keep the window open.
Fitting Instructions with Fittings
There are two types of crimp fittings - the so-called pressing and compression. They create completely different connections, so before starting work, you need to decide which connections you would like to see: one-piece or conditionally detachable.
Pressing elements are similar to solder fittings, but have shallow recesses with gaskets at the edges. Using special press tongs, which have a set of nozzles for different diameters, crimping is performed.
As a result, it creates a tight one-piece connection that cannot be repaired, and in case of an accident it is only possible to replace it.
In the store you can see the details that are identical at first glance, but they differ in characteristics (composition, wall thickness, etc.). Heating fittings marked in green
Pressing creates a strong, reliable connection of parts, while maintaining the geometry of the pipes and does not deform the connecting elements. There is a nuance of pressing “soft” copper products: before the operation, a support sleeve is inserted inside the pipe, which resists deformation of the compliant material
The pressing process is simple and does not take much time. From the tool you need a standard set for cutting and processing pipes, as well as press jaws with the right nozzle.
Image Gallery
Photo from
Step 1 - Choosing a Brass or Copper Fitting
Step 2 - connecting the copper pipe and fitting (angle, cross piece, adapter)
Step 3 - Marking Fitting Fitting Location
Step 4 - pressing with special press pliers
Pressing is considered a reliable method. If you plan to insulate copper pipes, then you can use insulation pipes that are easily worn even on curved structures. After pressing, the finished heating network can be masked in strobes, covered with decorative sheathing and poured with a screed.
The second type of fittings is compression. They differ in design and installation process.
Compression fitting for copper pipes is a prefabricated device consisting of three parts: a brass or copper body, a compression ring, also called a collet, and a nut
The crimping procedure is as follows:
- a nut loosens onto the prepared end of the pipe;
- then a collet is put on;
- Lastly, the fitting body is put on all the way;
- the nut is screwed by hand by thread, while pressing the split ring;
- the connection is reached with an adjustable or adjustable wrench.
During compression crimping, the cutting ring tightly wraps around the pipe, creating a strong and tight joint. The nut may loosen over time, so pipelines with this type of installation must be serviced regularly.
The connections are conditionally detachable, since they can be disassembled, however, if necessary, a fragment with a clamped ring will have to be removed and a new fitting installed.
Depending on the location of the pipeline, the diameter of the products and installation conditions, you can choose one or another method. Useful tips on their application are presented in the following videos.
Recommendations for pressing small and large diameter pipes:
How to solder:
Overview of all types of fittings:
Nuances of soldering - practical application:
Each method of connecting pipes has its own characteristics, which must be taken into account at the design stage. Crimp technology is seen as simpler, while soldering requires experience and professional skill.
If self-assembly of the pipeline seems difficult, we recommend that you invite a specialist to the assistants and, under his guidance, install the heating network from copper pipes.
If you have the necessary experience and knowledge in the installation of copper pipelines, share it with our readers. Perhaps you know some subtleties of installation that we did not mention in this article? Please leave your comments in the box below.